Resources Safety Data Sheet - here Resin Profile ( Click here ) a laboratory. Please note that certain specifications may be subject to change without prior notice. SAFETY DATA SHEET Engineering Series Resin, Tough 100E, Green Page 1 of 10 SECTION 1 : IDENTIFICATION 1.1 Product identifier Product name Engineering Series Resin, Tough 100E, Green Recommended use and restrictions on use Recommended use For use in Phrozen 3D-printers Restrictions on use Do not use in the situation that easily generate aerosol, steam. 1.2 Name, address and phone of manufacturer, importers or supplier Manufacturer Phrozen Tech Co., Ltd.287 Niupu Rd, Xiangshan Dist, Hsinchu City 30091, TAIWAN( R.O.C ) Phone +886-3621-0505 Emergency phone / Fax +886-3621-0505 / +886-3539-6591 SECTION 2 : HAZARD IDENTIFICATION 2.1 Hazard classification Acute toxicity (oral) Category 4, Skin corrosion/irritation Category 2, Serious eye damage/eye irritation Category 1, Skin sensitization Category 1, Specific target organ toxicity - single exposure (respiratory tract irritation) Category3 Specific target organ toxicity - repeated exposure Category 2 2.2 Signal statement Corrosion, Exclamation mark, Health hazard, 2.3 Pictograms 2.4 Signal word Danger 2.5 Hazard statements Harmful if swallowed Causes skin irritation Causes serious eye irritation May cause respiratory irritation. May cause damage to organs through prolonged or repeated exposure. SAFETY DATA SHEET Engineering Series Resin, Tough 100E, Green Page 2 of 10 2.6 Precautionary statements If medical advice is needed, have product container or label at hand. Keep out of reach of children. Do not breathe dust/fume/gas/mist/vapours/spray. Use only outdoors or in a well-ventilated area. Wear protective gloves/protective clothing/eye protection/face protection. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, If present and easy to do. Continue rinsing. Immediately call a POISON CENTER/doctor. Store in a well-ventilated place. Keep container tightly closed. Store locked up. Dispose of contents/container in accordance with local/regional/national/international regulations. 2.7 Other hazard None SECTION 3 : COMPOSITION / INFORMATION ON INGREDIENTS 3.1. Substances Not relevant (mixture) 3.2. Mixtures Components CAS number Weight % Classification acc. to GHS 2-Propenoic acid, 2-hydroxyethyl ester, polymer with 1,1'- methylenebis(4- isocyanatocyclohexane) and.alpha.alpha.'.alpha.''-1,2,3 73324-00-2 50 – 75% Skin Irrit. 2 / H315 Eye Irrit. 2 / H319 STOT SE 3 / H335 4-(1-oxo-2-propenyl)-morpholine 5117-12-4 25 – 50% Acute Tox. 4 / H302 Eye Dam. 1 / H318 Skin Sens. 1 / H317 STOT RE 2 / H373 Additives1 Trade Secret 2-5% Eye Irrit. 2 / H319 Skin Sens. 1B / H317 SAFETY DATA SHEET Engineering Series Resin, Tough 100E, Green Page 3 of 10 SECTION 4 : FIRST AID MEASURES 4.1. First-aid advice and recommendations for different routes of exposure 4.1.1 Inhalation If breathing is irregular or stopped, immediately seek medical assistance and start first aid actions. In case of respiratory tract irritation, consult a physician. Provide fresh air. 4.1.2 Skin Contact Wash with plenty of soap and water. 4.1.3 Eyes Contact Remove contact lenses, if present and easy to do. Continue rinsing. Irrigate copiously with clean, freshwater for at least 10 minutes, holding the eyelids apart. 4.1.4 Ingestion Rinse mouth with water (only if the person is conscious). Do NOT induce vomiting. 4.2. Most important symptoms and hazardous effecects None 4.3. Protection of First-aid personnel None 4.4. Note for physician None SECTION 5 : FIRE-FIGHTING MEASURES 5.1 Applicable extinguishing media Water spray, BC-powder, Carbon dioxide (CO2) 5.2 Specific hazards confronted during fire fighting Carbon monoxide (CO), Carbon dioxide (CO2) 5.3 Specific fire-fighting procedure None Aquatic Chronic 3 / H412 Additives2 Trade Secret 2-5% Skin Sens. 1A / H317 Repr. 2 / H361d Aquatic Chronic 2 / H411 SAFETY DATA SHEET Engineering Series Resin, Tough 100E, Green Page 4 of 10 5.4 Specific protecttive equipments for fire-fighters In case of fire and/or explosion do not breathe fumes. Co-ordinate firefighting measures to the fire surroundings. Do not allow firefighting water to enter drains or water courses. Collect contaminated firefighting water separately. Fight fire with normal precautions from a reasonable distance. SECTION 6 : ACCIDENTAL RELEASE MEASURES 6.1. Personal precautions Wear breathing apparatus if exposed to vapours/dust/spray/gases. 6.2. Environmental precautions Keep away from drains, surface and ground water. Retain contaminated washing water and dispose of it. 6.3. Cleaning methods Wipe up with absorbent material (e.g. cloth, fleece). Collect spillage: sawdust, kieselgur(diatomite), sand, universal binder. Covering of drains. Place in appropriate containers for disposal. Ventilate affected area. SECTION 7 : SAFETY HANDLING AND STORAGE 7.1. Handling Use local and general ventilation. Use only in well-ventilated areas. Do not eat, drink and smoke in work areas. Remove contaminated clothing and protective equipment before entering eating areas. Wash hands after use. Never keep food or drink in the vicinity of chemicals. Never place chemicals in containers that are normally used for food or drink. 7.2. Storage Storage at the area of cool,dry. Keep away from heat,direct sunlight, rainy and rapid temperature. Storage temperature between 15°C/ 59°C to 35°C / 95°F. Close the lid tightly when not in use. SAFETY DATA SHEET Engineering Series Resin, Tough 100E, Green Page 5 of 10 SECTION 8 : EXPOSURE CONTROLS / PERSONAL PROTECTION 8.1. Engineering controls Provide adequate ventilation to the areas where the product is stored and/or handled. 8.2. Control Parameters Component TWA STEL CEILING BEI s Titanium dioxide 10 mg / m 3 15 mg /m 3 - - 8.3. Personal protective equipment 8.3.1 Respiratory protection In case of inadequate ventilation wear respiratory protection. Filtering half mask (EN 149). P1 (filters at least 80 % of airborne particles, colour code: White). 8.3.2 Hand protection Chemical protection gloves are suitable, which are tested according to EN 374. For example : NBR: acrylonitrile-butadiene rubber Material thickness : ≥ 0.6mm Breakthrough times of the glove material : > 480 minutes (permeation: level 6) 8.3.3 Eye protection Use safety goggles. 8.3.4 Skin protection Use clothing that provides complete protection to the skin. 8.4. Hygiene measures Do not eat, drink and smoke in work areas. Wash thoroughly after handling. Keep clean of operation area. Take off polluted clothing as soon as possible after work. The clothing can be re-wear only after washed in clean or discard. SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES Apperance and color Green viscous liquid Odor Typical acrylate Odor threshold N/A Melting point N/A pH value 6-8 Boiling point >360 °C at 100.7 kPa SAFETY DATA SHEET Engineering Series Resin, Tough 100E, Green Page 6 of 10 Flammable N/A Flash point Testing method >110°C Close up Decomposition Temp N/A Natural Temp N/A Explosive limit N/A Vapor pressure 0.059 Pa at 20 °C Vapor density N/A Density 1.08 g /cm³ at 25 °C Solubility N/A Octanol/water distribution coefficient (log Kow) url: https://cdn.shopify.com/s/files/1/0436/6965/1618/files/SDS-Phrozen-Engineering_Series_Resin_Tough_100E_Green-EN.pdf?v=1733189906 local: SDS-Phrozen-Engineering_Series_Resin_Tough_100E_Green-EN.pdf Fonte: phrozen3d.com/pages/resin-profile (widget por impressora — settings de exposição por modelo). [perfis de impressão NÃO incluídos nesta auditoria — decisão do Eduardo; disponíveis em info.phrozen3d.com/pages/resin-profile por impressora] - Green / 1 KG - Black / 1 KG - preço: NÃO capturado (regra) - img01 · https://cdn.shopify.com/s/files/1/0797/4774/4027/files/Tough-100E_Black_1400x1600_1_6605e0f8-337b-4dc0-9eee-de0f4a00b5fd.png?v=1733299957 - img02 · https://cdn.shopify.com/s/files/1/0797/4774/4027/files/Tough-100E_Black_1400x1600_2_dce279a3-b26d-4536-937f-6bdefb07dbdd.png?v=1733299957 - img03 · https://cdn.shopify.com/s/files/1/0797/4774/4027/files/Tough-100E_Black_1400x1600_3_233e6ab9-fe83-4487-a216-f8c6326df774.png?v=1733299957 - img04 · https://cdn.shopify.com/s/files/1/0797/4774/4027/files/Tough-100E_Black_1400x1600_4_5ceb90ae-8921-4927-93ea-3f371d321cca.png?v=1733299957 - img05 · https://cdn.shopify.com/s/files/1/0797/4774/4027/files/Tough-100E_1400x1600_5_57faf055-4b89-435a-a756-79fae8ededd6.png?v=1733299957 - img06 · https://cdn.shopify.com/s/files/1/0797/4774/4027/files/Tough-100E_Green_1400x1600_1_1fa87f79-cda9-4049-8a48-9c87232f9e98.png?v=1733299957 - img07 · https://cdn.shopify.com/s/files/1/0797/4774/4027/files/Tough-100E_Green_1400x1600_2_2bcbc699-d136-47e5-aaed-b7fd2410da00.png?v=1733299957 - img08 · https://cdn.shopify.com/s/files/1/0797/4774/4027/files/Tough-100E_Green_1400x1600_3_f41130df-849d-465c-b57e-b6f272f3eb35.png?v=1733299957 - img09 · https://cdn.shopify.com/s/files/1/0797/4774/4027/files/Tough-100E_Green_1400x1600_4_c8697add-e162-41c8-990f-5b42c3474332.png?v=1733299957 - img10 · https://cdn.shopify.com/s/files/1/0797/4774/4027/files/800-450__Tough-100E_Landing-page-GIF_03_b9bfea40-c242-477b-8236-7a5d032fe492.gif?v=1732869111 fonte: shop global.phrozen3d.com (products.json body_html+imagens+variantes) + SDS de /pages/document SDS: 1 casados perfis de impressão: não incluídos (decisão) imagens: 10 pela NET preço: ⓐ ignorado por regra _O fornecedor não publica compatibilidade de máquina nesta página._